Marine Adhesives

TREADMASTER MARINE CONTACT ADHESIVE
Combining the benefits of a contact adhesive with  a high level of water resistance, this product provides and ideal method of fitting Treadmaster. With no mixing and the  ability to walk on the deck immediately after fitting, Treadmaster Marine Contact is ideal for fixing to fibreglass, wood or steel decks. Preparation and application details shown on the can.(Click here)

TREADMASTER MARINE ADHESIVE
This two pack epoxy adhesive is designed to provide the ultimate in bonding performance. Ideal for use on a wide range of deck materials, it  provides a bond which is suitable for the most arduous of conditions. Full instructions are on can.(Click here)

COVERAGE: 1200 x 2700mm (3 Sheets)

MRRP: £41.52 ex. VAT

COVERAGE: 1200 x 900mm (1 Sheet)

MRRP: £17.46 ex. VAT

INSTRUCTIONS FOR USE  (Contact Adhesive)

Surface preparation

Surfaces must be clean, dry and free from oil and grease.

Existing paint, vanish, waxes, polishes, etc., must be removed.

Application

Stir thoroughly before use.  The adhesive can be applied by brush or roller coater.  Cut the Treadmaster to shape and mask off the deck area to fit exactly the Treadmaster panel. A space of 1-2" should be left between adjacent panels.  Apply a thin, even coat of adhesive to both surfaces, work fairly quickly and take care to keep the adhesive away from the face side of the Treadmaster. Allow to dry until the adhesive is only just touch dry (5 - 10 minutes depending on temperature). Then align the panel carefully and bring into contact with the deck surface, applying firm pressure, preferably with a small hand roller over the whole panel. Work from the centre to the edge to avoid air entrapment.

Storage Conditions

Keep containers closed and in a cool (10°C - 20°C) dry place away from direct sunlight.

INSTRUCTIONS FOR USE  (2 Pack Epoxy)

One complete pack is sufficient for one full 1200 x 900 mm sheet of Treadmaster. If smaller quantity is required, Part A and Part B should be mixed in equal amounts.

Surface preparation

Surfaces must be clean, dry and free from oil and grease.  Existing paint, vanish, waxes, polishes, etc., must be removed. Fiberglass, aluminium and steel surfaces should be lightly abraded with a nylon scouring pad and all dust removed.

Mixing

Prepare the Treadmaster and deck before mixing the resine. Transfer the contents of container B into container A and mix thoroughly until the colour is consistent throughout the mix.

Once mixed, the adhesive must be used without delay - under average environmental conditions a pot life of 20 minutes in the tin can be expected.  Spreading the adhesive on to a flat plate after mixing will extend the useful pot life by helping to dissipate heat generated by the curing reaction.

The adhesive should not be used when ambient temperatures are below 10°C or above 30°C.

Immediately after use, clean tools, mixing vessels, brushes, etc. with methylated spirit

Application

Apply adhesive using a serrated scraper, to the underside of the Treadmaster and to the surface to which it is to be bonded. Position the Treadmaster and carefully roll from centre to edge, apply pressure to consolidate the adhesive layers, ensuring that no air is trapped between the surfaces.

Where possible, adhesive should be allowed to extrude between the edges of adjacent mats, to give a positive seal against ingress of water.  Excess adhesive should be wiped off promptly with methylated spirit. Depending on environmental conditions the adhesive will begin to set in 2 - 4 hours and full strength will be achieved after 24 hours.

We Regret that due to excessive carriage charges TREADMASTER CONTACT ADHESIVE is only available to buy On-line in the UK Mainland ONLY, NONE UK Mainland PLEASE CONTACT US BEFORE ORDERING as carriage will be CHARGED AT COST. PLEASE see our Distributor list for your nearest supplier.

We Regret that due to excessive carriage charges TREADMASTER MARINE ADHESIVE is only available to buy On-line in the UK Mainland ONLY,  NONE UK Mainland PLEASE CONTACT US BEFORE ORDERING as carriage will be CHARGED AT COST. PLEASE see our Distributor list for your nearest supplier.

Information in this document and otherwise supplied to users is based on our general experiences and is given in good faith but, because of particular factors which are outside our knowledge and control and affect the use of products, no warranty is given or implied with respect to such information.

Specifications are subject to change without notice. A safe handling data sheet on this material is available as a PDF download. Click here to download

Please contact our Webmaster with questions or comments. © Copyright 2008 Tiflex Limited. All rights reserved.

ALL Prices are for UK ONLY.  For overseas pricing please contact us.

Treadmaster Marine spring offers are available to online customers ONLY. Promotions may end at anytime without notice.